Can I Install a Bath Tub Myself? Factors to Consider And Also Steps
Can I Install a Bath Tub Myself? Factors to Consider And Also Steps
Blog Article
Here below you can locate a lot of amazing content involving A Step-by-Step Guide to Installing a Bathtub.
Installing a tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, and sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a moderately tough task. If the old tub is easily obtainable, the task can move immediately; if you need to open up a wall to eliminate the old bathtub as well as place the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the new one. Make certain you have actually certified yourself for the job as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This article will assist you set up a brand-new bathtub in your restroom if you have already purchased a new tub as well as don't need to alter the setup of your previous water supply pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited gain access to that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous type ought to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub until the level reviews level.
To install faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the supply of water and also check all joints and new pipework for leaks as well as tighten them if needed. Load the tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the tub must wait till the bathtub has been utilized at the very least once as this will resolve it right into its last position.
Planning for the Installation
First of all, the sustaining structure provided with the bath should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last position.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, leading to problems with wetness as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to enable the activity experienced when the bathtub is in usage. The sealant can crack rather early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our topic on A Step-by-Step Guide to Installing a Bathtub. Thanks so much for taking the time to read our article post. In case you appreciated our article if you please don't forget to share it. I enjoy reading our article about Tools You Need to Install a New Bathtub .
Visit Homepage
Report this page